Ir al contenido

INR18650-35E — celda de ion-litio 18650

Samsung SDI INR18650-35E: 3,500 mAh nominal (3,350 mAh minimum), 3.6 V nominal, 8 A continuous discharge, 50.0 g max, initial AC impedance at or below 35 mΩ.

Samsung SDI18650NMC3.6 V3,500 mAh8 A de descarga

Especificaciones

Parámetros de INR18650-35E

ParámetroValor
MarcaSamsung SDI
ModeloINR18650-35E
Formato18650
QuímicaNMC
Tensión nominal3.6 V
Capacidad típica3,500 mAh
Corriente de descarga8 A

Acerca de Samsung SDI INR18650-35E 18650 Li-ion Cell 3,500 mAh 8 A

The INR18650-35E is the capacity end of Samsung's 18650 range: 3,500 mAh at 8 A continuous. Specify it where runtime per cell is the design driver and peak current stays modest — solar lighting, remote monitoring, medical devices, anything that discharges slowly for hours.

Why pack builders specify it

  • 3,500 mAh nominal, 1,000 mAh more than the 25R in the same 18650 can
  • 8 A continuous covers the large majority of sensor, lighting and portable electronics loads
  • Low self-discharge suits equipment that sits idle between uses
  • Long production run and wide availability keep pack cost predictable

Typical applications

  • Solar and area lighting – Overnight runtime per cell drives the design; discharge is a fraction of an amp
  • Power banks and portable electronics – Maximum stored energy in a standard 18650 holder
  • Medical and monitoring devices – Infusion pumps, portable monitors and diagnostic handhelds with steady low draw
  • Remote sensors and IoT – Long deployment intervals between service visits

Where it fits

Choose the 35E for capacity-first designs under 8 A. Above that, the 30Q covers up to 15 A and the 25R up to 20 A. Do not put the 35E in a high-drain tool or drone pack — the impedance is too high and the cell will run hot.

Charging and pack integration

Charge CC-CV to 4.2 V within the current limits listed above and stop discharge at 2.5 V. These are unprotected industrial cells: a BMS or protection circuit is required, interconnects must be resistance or laser welded rather than soldered, and cells of different model, batch or state of charge must not be mixed in one pack. Charging below 0 °C is not permitted unless the pack implements a low-temperature charge strategy.

Certifications and documentation

UN38.3, MSDS, IEC 62133-2, UL 1642, CE, RoHS, REACH, PSE, KC, BIS, CB. UN38.3 test summary, MSDS and the cell specification are available on request.

Packaging

Quantity per box200 pcs
Gross weight per box11.2 kg

Specification basis: Official Samsung SDI spec + cross-checked.

Preguntas sobre esta celda

No. At 8 A continuous it is an energy cell. High-drain applications need the 25R or a Molicel P-series cell.
Samsung's reference is 500+ cycles under 0.5 C charge and 1 C discharge. Deeper discharge and higher current shorten that.
3,500 mAh is nominal; the minimum is 3,350 mAh. Size pack capacity from the minimum figure.

Comparativa

Otras celdas 18650 con las que comparar presupuesto

Modelo Marca Capacidad Descarga Ficha técnica
INR18650-MJ1 LG Energy Solution 3,500 mAh 10 A Pendiente
INR18650-30Q Samsung SDI 3,000 mAh 15 A Pendiente
INR18650-M35A Molicel 3,450 mAh 10 A En archivo
INR18650-25R Samsung SDI 2,500 mAh 20 A Pendiente

Las cifras de capacidad y descarga son los valores que constan para cada modelo; cuando no se dispone de la ficha técnica del fabricante, la fila figura como pendiente en lugar de presentarse como verificada.

¿Necesita INR18650-35E en volumen?

Confirme disponibilidad, documentación de lote y plazo de entrega antes de cerrar el diseño.

Solicitar presupuesto
WhatsApp