INR18650-MJ1 — celda de ion-litio 18650
LG Energy Solution INR18650-MJ1: 3,500 mAh typical, 3.635 V nominal, 10 A discharge. The higher-capacity sibling of the MH1 at 3,500 mAh, holding the same 10 A continuous ceiling. Choose it when pack volume is fixed and runtime is the constraint.
Especificaciones
Parámetros de INR18650-MJ1
| Parámetro | Valor |
|---|---|
| Marca | LG Energy Solution |
| Modelo | INR18650-MJ1 |
| Formato | 18650 |
| Química | NMC |
| Tensión nominal | 3.635 V |
| Capacidad típica | 3,500 mAh |
| Corriente de carga estándar | 1.7 A |
| Corriente de carga máx. | 3.4 A |
| Corriente de descarga | 10 A |
| Resistencia interna | AC ≤40 mΩ (1 kHz) |
| Peso | ≈49 g |
| Diámetro | ≈18.4 mm |
| Altura | ≈65.15 mm |
| Temperatura de carga | 0 °C to 45 °C |
| Temperatura de descarga | -20 °C to 60 °C |
INR18650-MJ1 — specification and pack integration
The higher-capacity sibling of the MH1 at 3,500 mAh, holding the same 10 A continuous ceiling. Choose it when pack volume is fixed and runtime is the constraint.
What the numbers mean for a pack
- 3,500 mAh typical in a 18650 can, at 3.635 V nominal
- 10 A discharge ceiling — the pack design must hold the cell inside its temperature cut-off to use it
- 3.4 A maximum charge current sets the fastest realistic turnaround
- AC ≤40 mΩ (1 kHz) — the figure that decides voltage sag under load
Where it is used
- Flashlights, headlamps and handheld instruments
- Light-duty cordless tools
- Telecom and industrial backup packs where energy density drives cell count
Integration notes
Charge CC-CV to 4.2 V within the current limits above and stop discharge at 2.5 V. These are unprotected industrial cells: a BMS or protection circuit is required, interconnects must be resistance or laser welded rather than soldered, and cells of different model, batch or state of charge must not be mixed in one pack. Charging below 0 °C is not permitted unless the pack implements a low-temperature charge strategy.
Documentation
UN38.3 test summary, MSDS and the cell specification are available on request. Values shown here are pending verification against the manufacturer data sheet.
Specification basis: Publicly circulated LG specification — values pending verification against manufacturer datasheet
Comparativa
Otras celdas 18650 con las que comparar presupuesto
| Modelo | Marca | Capacidad | Descarga | Ficha técnica |
|---|---|---|---|---|
| INR18650-35E | Samsung SDI | 3,500 mAh | 8 A | Pendiente |
| INR18650-MH1 | LG Energy Solution | 3,200 mAh | 10 A | Pendiente |
| INR18650-M35A | Molicel | 3,450 mAh | 10 A | En archivo |
| NCR18650GA | Panasonic | 3,450 mAh | 10 A | Pendiente |
Las cifras de capacidad y descarga son los valores que constan para cada modelo; cuando no se dispone de la ficha técnica del fabricante, la fila figura como pendiente en lugar de presentarse como verificada.
Aplicaciones
Servicios para los que se especifica este grado de celda
Celdas para bicicletas eléctricas, scooters y tracción ligera
3,500 mAh at 10 A continuous — the balanced grade traction packs are built from.
Ver el perfil de servicio AplicaciónCeldas para almacenamiento residencial y comercial
3,500 mAh at low C-rate; capacity per cell is what binds in a storage enclosure.
Ver el perfil de servicioRelacionado
Otras vías de búsqueda
¿Necesita INR18650-MJ1 en volumen?
Confirme disponibilidad, documentación de lote y plazo de entrega antes de cerrar el diseño.